Material Handling Experts


Steel King SK2000 Pallet Racks

Assembly Instructions & Spec Information

SK2000 Tubular Pallet Racks SK2000 logoRead these instructions before assembling your storage rack system. To obtain the maximum benefit from any storage rack system, and for the safety of those around the rack, the rack must be properly assembled and maintained.

Storage racks should be assembled only by trained personnel, experienced with proper rack assembly procedures. If you are unfamiliar with rack assembly, you should contact Cisco-Eagle for professional rack assembly services.

Improper rack assembly can not only cause poor performance of your system, but can also pose a safety hazard in your facility.

It is very important that the rack structure be installed in a plumb, level, and square condition. Since few floors are perfectly flat, shimming of the racks is frequently required. A four-foot long carpenter level is a good choice for checking level and plumb conditions on storage racks of average proportions. A vertical tolerance of 1/8" in 4 feet (or other as specified on your installation drawings) is generally acceptable.

The rack structure should be assembled and used only as shown on assembly drawings.

Changing the configuration (such as adjusting storage levels) can adversely affect the load carrying capacity and reduce the structural integrity of the rack system. Before adjusting the rack configuration, contact Cisco-Eagle to verify the safety and structural adequacy of the new configuration.

"Nut and Bolt" connections are to be tightened to a snug and secure condition. 60 foot-pounds is typical for 1/2" diameter hardware, but tightening to the point of crushing tubular components is to be avoided.

Safety locks on boltless connections (SK2000 series) must be fully engaged through the beam connector and upright column connector holes. These safety locks help prevent accidental dislodgment of the load beams. The locks should engage automatically, however the beam needs to be fully seated, in the bottom of the teardrop shape connector hole.

Beams must not be used with damaged or missing safety locks. Extra safety locks are available from Cisco-Eagle.

Every column of each rack frame must be anchored to an adequate concrete floor.

The normal anchor connection is (1) 1/2" diameter x 3‐3/4" concrete expansion anchor per column, or as indicated on the installation drawings.

Anchor bolts are not included with rack systems unless specifically detailed on the Bill of Materials.

Since anchor bolts vary in strength, if you are purchasing your own anchor bolts, contact Cisco-Eagle for minimum anchor specifications for your installation.

Since concrete floors vary greatly in design and load carrying capacity, Steel King cannot guarantee that a particular concrete slab is adequate to support a particular rack installation. The characteristics of the slab should be obtained from the building architect before the racks are specified, so that the rack supplier can design the rack to suit the slab.

Do not install racks outdoors, unless specifically designed for this purpose. Outdoor usage requires consideration of wind loads, snow loads, etc., which are not normally considered in rack design.

Be cautious when intermingling new and existing parts. Even components produced by the same manufacturer can vary in design. Many manufacturers offer a variety of basic designs (for example bolted and boltless connections), and basic designs are often altered slightly over the years to improve performance. These differences can adversely affect the overall performance and safety of a rack structure.

Many storage rack systems have such similar designs that a rack system can be assembled using parts from more than one manufacturer. However, since Steel King has no control over the quality of components designed and manufactured by other firms, any and all warranties and guarantees are made void if non-Steel King parts are used in conjunction with Steel King parts.

Installation of "capacity plates" is strongly recommended. These plates should identify the characteristics for which the rack was designed, such as load size, load weight, and rack configuration. These plates are very useful for communicating safe loading information to both present and future users. Several signs should be prominently located for easy visibility, and be permanently affixed to the rack structure. Appropriate signs can be obtained locally, through industrial mail order catalogs, or from Cisco-Eagle.

Never climb on racks, during or after assembly. Storage racks are not designed to be stepped on or climbed on. A slip or fall may result in serious injury.

It is your responsibility to communicate this important warning to all who come into the proximity of your storage rack. This communication can include training and appropriate signage. If your rack is used in a retail environment, prominently placed, high visibility warning signs are especially helpful in preventing this misuse of a storage rack structure.

Allow adequate aisle spacing. Aisles which are too narrow for the handling equipment, or are reduced in size by obstructions (such as temporary floor stacking at rack row ends) increases the danger of collisions between the lifting equipment and the rack structure, and may cause a danger to pedestrian traffic.

Maintain adequate clearances around loads. These include those dictated by local fire codes (between loads in back to back rows, and overhead between the uppermost load and the roof structure). Also between adjacent loads horizontally, and between loads and rack horizontal and vertical members. Clearances which are too tight could increase fire risk, will decrease handling speed, and increase the likelihood of damage to rack components and/or loads.

Install good lighting in every rack aisle. Good lighting improves handling efficiency, prevents accidents, and reduces accidental damage to the rack structure.

Install optional column protectors at aisle facing rack columns, and guard rails at ends of rack rows. These devices provide a visual and physical barrier against accidental handling equipment impacts. A variety of these guarding devices are available from Steel King and your Steel King Distributor.

Do not cut, weld, or in any other way modify any component of your Steel King storage rack. Such modifications may decrease the load carrying capability of the component, and the weakened component can jeopardize the integrity of the entire rack structure. Any modification of any component, except as performed or authorized in writing by Steel King Industries, Inc. engineering personnel, will make null and void any warranties and guarantees.

Submit a Rack Inquiry, or call 888-877-3861 for immediate assistance.