Move the cursor over the thumbnails to see a larger image below.
405
Loading...
Panels can be set to extend above the top rack beam.
Panels can be set to extend above the top rack beam.
Panels can be set to extend above the top rack beam.
Rack Cage is designed for teardrop-style pallet racks
Rack guards can be installed on any rack,
but require different hardware. These are configured for teardrop style
racks. If your rack is another type, contact us for assistance.
Especially in areas where case picking, pallet flow, and flow racks are used for the bottom row with bulk storage above, Rack Back panels protect employees from falling items by making sure nothing can come loose when pushed by a lift truck or if the pallet breaks. Wire barriers can be ordered flush or offset to allow pallet overhang; just specify when you order flush or overhang, and the amount of overhang needed.
Attractive and easy to install: These wire rack backing panels install easily and quickly, with several mounting options to fit your specific needs. Clean, straight-line design makes for a very attractive warehouse area. They’re finished in gray, but you can specify other colors (costs may vary).
Built tough: Constructed from 2" x
2", 10-gauge welded wire mesh and securely welded into a frame of 1-1/4" x 1-1/4" x 13 gauge steel angle.
Standard sized panels 4’ 0" or 5’ 0" high, match beam length in width. Stack panels one on top of the other to top of rack system.
Custom size panels available to fit any rack size or configuration.
Panels attach directly to rack with mounting brackets.
Off set brackets allow for load to overhang rack beams.
Multiple attachment points (seven) on ends of each panel.
Assembly hardware is inaccessible from the exterior of the partition.
Panels can be mounted to support posts-if stand alone system desired.
"Above the Top" mounting allows panels to extend above top rack beam
(contact us for details).
Angle frame design gives installer clear access to hardware, speeding
installation.
Standard 3/8" assembly hardware is the heaviest in the industry.
System may be started at the floor or at any level where protection is
required.
Heavier options available.
We also offer secure wire mesh enclosures to completely enclose your racks, creating a highly-secure barrier that helps you eliminate pilferage while making your warehouse safer.
Ordering Dimensions:
RackBack protective welded wire mesh panels are approximately the same width as your rack beam. Order to match beam width; the wire panels are around 6" narrower, to fit between posts.
Specify the
height dimension by matching it to the same height of your rack frame. The wire enclosure is flush with the top of your frames.
Select mounting option when you order. Utilize flush or offset mount;
see below for details.
Mounting Options (select when you order)
Flush Mounted
(LEFT) the rack backing is flush mounted directly to the pallet rack
uprights. This provides the tightest possible access. Not even a hand
can get through to stored items.
Offset Mounted
PaPanels mount to the pallet rack upright with an off-set bracket. Off-set
brackets from 0"-12" available. With offset mounting, you can overhang
pallets from your rack, 1" to 12" (specify when you order).
If you have questions about your rack system protection options, contact us.
Panels
Shall be 10 gauge steel wire welded into 2" x 2" center to center square mesh, securely welded into a frame of 1-1/4" x 1-1/4" x 13 gauge steel angle factory punched with 7/8" x 7/16" slotted holes to accept 3/8" mounting hardware. Holes on vertical frame shall be punched on 6" centers. Panels six or seven feet wide shall have one 1/4" x 3/4" flat stiffener, wider panels receive two 1/4" x 3/4" stiffeners. Panels wider than ten feet shall be framed in 1-1/2" x 1-1/2" x 1/8" steel angle and receive three flat stiffeners.Posts
(optional) Shall be made of 2" x 2" x 14 gauge steel tubing. Base plates of 2" x 7" x 1/4" steel flat with two 7/16" round holes for anchoring, shall be welded to each tube. Posts are factory drilled with 1/2" holes to accept hardware for mounting panels.Hardware
Shall be 3/8" standard thread grade two plated nuts and bolts. Floor anchors are 3/8" wedge type-provided.Finish
Non-plated parts are powder coated grey. Touch up paint included with each shipment.
We're here to help you
Cisco-Eagle provides speedy service and expert assistance on all material handling products. If you need help of any kind, please contact us.
Call Toll Free: 888-877-3861, 7AM-5PM Central Time
Customer Center: Inquiry forms for fast response
Product Tools
About Cisco-Eagle
Downloads & Tools
Home
Customer
Service
Cart
Quote Builder
Login
