Welded Stadium Lockers Specifications
Welded Stadium? Locker Overview
Welded Penco Stadium? lockers have an open front and perforated sides providing
a fully ventilated space for storage of athletic gear or other items. The base
model is an open shell with a full width shelf. A security box fastened to the
shelf and a foot locker with a hinged, reinforced seat at the base are popular
options. They are available in 24" or 33" widths and 18", 21" or 24" depths.
Welded Stadium lockers are 76" high, which includes a 4" high integral base.
STADIUM LOCKER WELDED SPECIFICATIONS
MATERIALS SHEET STEEL: All parts made from prime grade mild cold rolled sheet
steel free from surface imperfection, and capable of taking a high grade enamel
finish.
FINISHING: Chemically pretreat metal with a six stage cleaning phosphatizing and
metal preparation process. Finish coat shall be electrostatically applied powder
coat enamel baked on at 350 to 400 degrees. Select colors from manufacturer's
minimum standard 21 colors. All lockers shall be painted inside and outside with
the same color.
EQUIPMENT: Coat hooks and coat rods are zinc plated. Truss fin head bolts and
hex nuts are zinc coated.
FABRICATION GENERAL CONSTRUCTION: Fabricate lockers square, rigid and without
warp. Metal faces shall be flat and free of distortion. Lockers shall be
pre-assembled of welded construction, all welds shall be free of burrs.
LOCKER FRAME: Locker frame member to be not less than 16 gauge formed to a
channel shape. Intermembering parts to be mortised and tenoned and electrically
welded together in a rigid assembly capable of resisting strains. BODY: All
locker body components shall be made of cold rolled steel specially formed for
added strength and rigidity and to ensure tight joints at fastening points.
Tops, bottoms and sides shall be 16 gauge. Bottoms have two reinforcement
channels for added strength. Backs shall be 18 gauge. SHELF: 16 gauge with four
sides formed to 90 degrees, the front edge shall have a second bend.
VENTILATION: For maximum ventilation locker has an open front. Side panels are
to be perforated with diamond-shaped openings unless otherwise specified.
NUMBER PLATES: Each locker to be supplied with a polished aluminum number plate,
2-1/4" wide x 1" high, with black numerals not less than 3/8" high. Number
plates to be attached to the center of shelf with two aluminum rivets.
INTERIOR EQUIPMENT: Each locker is provided with a set of rod holders, one coat
rod and two single prong hooks (to be fastened to the back panel).
OPTIONS
SECURITY BOX: 14 gauge lockable door with a 16 gauge side panel. The
door is attached to a welded frame with a continuous hinge. The hinge is mounted
to door with aluminum rivets. The door is locked through a single point latch
with a padlock or built in lock. A lock hole cover plate shall be provided for
use with padlocks. Security box door frame to be not less than 16 gauge formed
to a channel shape. Vertical members to have an additional flange to provide a
continuous door strike. Intermembering parts to be mortised and tenoned and
electrically welded together in a rigid assembly capable of resisting strains.
FOOT LOCKER: Front foot locker panel includes single point latch with padlock
strike plate and mini louvers. Top of foot locker opens with a continuous hinge,
opening and closing is quieted by rubber bumpers mounted to the contact points.
Seat is strengthened with two reinforcement channels welded to bottom of seat.
Two side seat supports are bolted to side panels and inserted in a support tab
on the front locker panel for added strength.
SOLID SIDE PANELS: Side panels shall be void of ventilation perforations.
EXECUTION INSTALLATION: Install metal lockers at location shown in accordance
with manufacturers instructions for plumb, level, and flush installation.
ANCHOR LOCKERS to the floor and wall 48" on center or less as recommended by the
manufacturer.
ADJUST & CLEAN: Adjust doors and latches to operate without binding. Verify that
latches are operating satisfactorily.
TOUCH UP marred finishes with factory supplied paint.
ACCEPTABLE MANUFACTURERS 1. Penco Products, Inc., Oaks, PA - Stadium Locker
PENCO RESERVES THE RIGHT TO VARY SPECIFICATIONS CONSISTENT WITH ITS POLICY OF
CONTINUOUS PRODUCT IMPROVEMENT.
11/11/2004
